Ürünler
Endüktif Sensör Pepperl Fuchs NJ50-FP-E-P1
29 Ocak 2019Endüktif Sensör Pepperl Fuchs NJ50-FP-E-P4-V1
29 Ocak 2019
Endüktif Sensör Pepperl Fuchs NJ50-FP-E-P2
Sensör
Yakınlık Sensörü
Proximity Sensor
Endüktif Proximity Sensör
Inductive Proximity Sensor
Pepperl Fuchs
Pepperl Fuchs Sensör
Pepperl Fuchs Proximity Sensor
Pepperl Fuchs Yakınlık Sensörü
Pepperl Fuchs Endüktif Proximity Sensör
Pepperl Fuchs Inductive Proximity Sensor
Pepperl Fuchs NJ50-FP-E-P2
Pepperl NJ50-FP-E-P2
NJ50-FP-E-P2
Açıklama
Pepperl Fuchs NJ50-FP-E-P2 Endüktif Sensör
Pepperl NJ50-FP-E-P2 Inductive Sensor
Yaklaşım Sensörü Pepperl Fuchs NJ50-FP-E-P2
Pepperl Fuchs NJ50-FP-E-P2 Yakınlık Sensörü
Inductive Sensor NJ50-FP-E-P2 Pepperl-Fuchs
Endüktif Sensör NJ50-FP-E-P2 Pepperl-Fuchs
Teknik veriler NJ50-FP-E-P2
| General specifications | ||
| Switching function | Normally open (NO) | |
| Output type | NPN | |
| Rated operating distance | 50 mm | |
| Installation | non-flush | |
| Output polarity | DC | |
| Assured operating distance | 0 … 40.5 mm | |
| Reduction factor rAl | 0.4 | |
| Reduction factor rCu | 0.3 | |
| Reduction factor r304 | 0.85 | |
| Output type | 3-wire | |
| Nominal ratings | ||
| Operating voltage | 10 … 60 V | |
| Switching frequency | 0 … 100 Hz | |
| Hysteresis | typ. 3 % | |
| Reverse polarity protection | yes | |
| Short-circuit protection | yes | |
| Voltage drop | ≤ 3 V | |
| Operating current | 0 … 200 mA | |
| Off-state current | 0 … 0.5 mA typ. 0.1 µA at 25 °C | |
| No-load supply current | ≤ 20 mA | |
| Operating voltage indicator | LED, green | |
| Switching state indicator | LED, yellow | |
| Standard conformity | ||
| Standards | EN 60947-5-2:2007 IEC 60947-5-2:2007 |
|
| Approvals and certificates | ||
| UL approval | cULus Listed, General Purpose | |
| CSA approval | cCSAus Listed, General Purpose | |
| Ambient conditions | ||
| Ambient temperature | -25 … 70 °C (-13 … 158 °F) | |
| Mechanical specifications | ||
| Information for connection | A maximum of two conductors with the same core cross section may be mounted on one terminal connection! tightening torque 1.2 Nm + 10 % |
|
| Core cross-section | up to 2.5 mm2 | |
| Minimum core cross-section | without wire end ferrule 0.5 mm2 , with connector sleeves 0.34 mm2 | |
| Maximum core cross-section | without wire end ferrule 2.5 mm2 , with connector sleeves 1.5 mm2 | |
| Housing material | Crastin (PBTB) | |
| Sensing face | PBT | |
| Degree of protection | IP67 | |
