Ürünler
Endüktif Sensör Pepperl Fuchs NJ30+U4+N
28 Ocak 2019Endüktif Sensör Pepperl Fuchs NJ30P+U1+A2
28 Ocak 2019
Endüktif Sensör Pepperl Fuchs NJ30P+U1+1N
Sensör
Yakınlık Sensörü
Proximity Sensor
Endüktif Proximity Sensör
Inductive Proximity Sensor
Pepperl Fuchs
Pepperl Fuchs Sensör
Pepperl Fuchs Proximity Sensor
Pepperl Fuchs Yakınlık Sensörü
Pepperl Fuchs Endüktif Proximity Sensör
Pepperl Fuchs Inductive Proximity Sensor
Pepperl Fuchs NJ30P+U1+1N
Pepperl NJ30P+U1+1N
NJ30P+U1+1N
Açıklama
Pepperl Fuchs NJ30P+U1+1N Endüktif Sensör
Pepperl NJ30P+U1+1N Inductive Sensor
Yaklaşım Sensörü Pepperl Fuchs NJ30P+U1+1N
Pepperl Fuchs NJ30P+U1+1N Yakınlık Sensörü
Inductive Sensor NJ30P+U1+1N Pepperl-Fuchs
Endüktif Sensör NJ30P+U1+1N Pepperl-Fuchs
Teknik veriler NJ30P+U1+1N
| General specifications | ||
| Switching function | Normally open (NO) | |
| Output type | NAMUR | |
| Rated operating distance | 30 mm | |
| Installation | non-flush | |
| Assured operating distance | 1 … 24.3 mm | |
| Reduction factor rAl | 1 | |
| Reduction factor rCu | 1 | |
| Reduction factor rSt37 | 0 | |
| Reduction factor rBrass | 1 | |
| Output type | 2-wire | |
| Nominal ratings | ||
| Nominal voltage | 8 V | |
| Switching frequency | 0 … 150 Hz | |
| Current consumption | ||
| Measuring plate not detected | max. 1 mA | |
| Measuring plate detected | min. 3 mA | |
| Functional safety related parameters | ||
| MTTFd | 3636 a | |
| Mission Time (TM) | 20 a | |
| Diagnostic Coverage (DC) | 0 % | |
| Compliance with standards and directives | ||
| Standard conformity | ||
| NAMUR | EN 60947-5-6:2000 IEC 60947-5-6:1999 |
|
| Approvals and certificates | ||
| FM approval | ||
| Control drawing | 116-0165 | |
| UL approval | cULus Listed, General Purpose | |
| CSA approval | cCSAus Listed, General Purpose | |
| CCC approval | CCC approval / marking not required for products rated ≤36 V | |
| Ambient conditions | ||
| Ambient temperature | -25 … 70 °C (-13 … 158 °F) | |
| Mechanical specifications | ||
| Connection type | screw terminals | |
| Information for connection | A maximum of two conductors with the same core cross section may be mounted on one terminal connection! tightening torque 1.2 Nm + 10 % |
|
| Core cross-section | up to 2.5 mm2 | |
| Minimum core cross-section | without wire end ferrule 0.5 mm2 , with connector sleeves 0.34 mm2 | |
| Maximum core cross-section | without wire end ferrule 2.5 mm2 , with connector sleeves 1.5 mm2 | |
| Housing material | PBT | |
| Sensing face | PBT | |
| Degree of protection | IP68 | |
| Note | Tightening torque: 1.8 Nm (housing) | |
| General information | ||
| Use in the hazardous area | see instruction manuals | |
| Category | 2G | |
