Ürünler
Endüktif Sensör Pepperl Fuchs NBB15-U1-A2-V1
28 Aralık 2018
Endüktif Sensör Pepperl Fuchs NBB15-U1-E0
28 Aralık 2018
Endüktif Sensör Pepperl Fuchs NBB15-U1-A2-Y279075
Sensör
Yakınlık Sensörü
Proximity Sensor
Endüktif Proximity Sensör
Inductive Proximity Sensor
Pepperl Fuchs
Pepperl Fuchs Sensör
Pepperl Fuchs Proximity Sensor
Pepperl Fuchs Yakınlık Sensörü
Pepperl Fuchs Endüktif Proximity Sensör
Pepperl Fuchs Inductive Proximity Sensor
Pepperl Fuchs NBB15-U1-A2-Y279075
Pepperl NBB15-U1-A2-Y279075
NBB15-U1-A2-Y279075
Açıklama
Pepperl Fuchs NBB15-U1-A2-Y279075 Endüktif Sensör
Pepperl NBB15-U1-A2-Y279075 Inductive Sensor
Yaklaşım Sensörü Pepperl Fuchs NBB15-U1-A2-Y279075
Pepperl Fuchs NBB15-U1-A2-Y279075 Yakınlık Sensörü
Inductive Sensor NBB15-U1-A2-Y279075 Pepperl-Fuchs
Endüktif Sensör NBB15-U1-A2-Y279075 Pepperl-Fuchs
Teknik veriler NBB15-U1-A2-Y279075
| General specifications | ||
| Switching function | complementary | |
| Output type | PNP | |
| Rated operating distance | 15 mm | |
| Installation | flush | |
| Output polarity | DC | |
| Assured operating distance | 0 … 12.15 mm | |
| Reduction factor rAl | 0.33 | |
| Reduction factor rCu | 0.3 | |
| Reduction factor r304 | 0.74 | |
| Reduction factor rBrass | 0.41 | |
| Output type | 4-wire | |
| Nominal ratings | ||
| Operating voltage | 10 … 30 V DC | |
| Switching frequency | 0 … 200 Hz | |
| Hysteresis | typ. 5 % | |
| Reverse polarity protection | reverse polarity protected | |
| Short-circuit protection | pulsing | |
| Voltage drop | ≤ 2 V | |
| Operating current | 0 … 200 mA | |
| Off-state current | 0 … 0.5 mA | |
| No-load supply current | ≤ 20 mA | |
| Time delay before availability | 80 ms | |
| Operating voltage indicator | LED, green | |
| Switching state indicator | LED, yellow | |
| Functional safety related parameters | ||
| MTTFd | 1230 a | |
| Mission Time (TM) | 20 a | |
| Diagnostic Coverage (DC) | 0 % | |
| Compliance with standards and directives | ||
| Standard conformity | ||
| Standards | EN 60947-5-2:2007 EN 60947-5-2/A1:2012 IEC 60947-5-2:2007 IEC 60947-5-2 AMD 1:2012 |
|
| Approvals and certificates | ||
| CCC approval | CCC approval / marking not required for products rated ≤36 V | |
| Ambient conditions | ||
| Ambient temperature | -25 … 85 °C (-13 … 185 °F) | |
| Mechanical specifications | ||
| Connection type | M20 terminal compartment, core cross section ≤ 2.5 mm2 | |
| Information for connection | A maximum of two conductors with the same core cross section may be mounted on one terminal connection! tightening torque 1.2 Nm + 10 % |
|
| Core cross-section | up to 2.5 mm2 | |
| Minimum core cross-section | without wire end ferrule 0.5 mm2 , with connector sleeves 0.34 mm2 | |
| Maximum core cross-section | without wire end ferrule 2.5 mm2 , with connector sleeves 1.5 mm2 | |
| Housing material | PA/metal with epoxy powder coating | |
| Sensing face | PA | |
| Housing base | plastic | |
| Degree of protection | IP68 / IP69K | |
| Mass | 225 g | |
| Note | Tightening torque: 1.8 Nm (housing) Tightening torque of double flange: 4,5 Nm Tightening torque of mountig base: 2,7 Nm Tightening torque of cap nut: 10 Nm |
|
