Ürünler
Endüktif Sensör Pepperl Fuchs NJ20E-F34-E3-Y38055
28 Ocak 2019Endüktif Sensör Pepperl Fuchs NJ20P+U4+A2
28 Ocak 2019
Endüktif Sensör Pepperl Fuchs NJ20P+U1+A2
Sensör
Yakınlık Sensörü
Proximity Sensor
Endüktif Proximity Sensör
Inductive Proximity Sensor
Pepperl Fuchs
Pepperl Fuchs Sensör
Pepperl Fuchs Proximity Sensor
Pepperl Fuchs Yakınlık Sensörü
Pepperl Fuchs Endüktif Proximity Sensör
Pepperl Fuchs Inductive Proximity Sensor
Pepperl Fuchs NJ20P+U1+A2
Pepperl NJ20P+U1+A2
NJ20P+U1+A2
Açıklama
Pepperl Fuchs NJ20P+U1+A2 Endüktif Sensör
Pepperl NJ20P+U1+A2 Inductive Sensor
Yaklaşım Sensörü Pepperl Fuchs NJ20P+U1+A2
Pepperl Fuchs NJ20P+U1+A2 Yakınlık Sensörü
Inductive Sensor NJ20P+U1+A2 Pepperl-Fuchs
Endüktif Sensör NJ20P+U1+A2 Pepperl-Fuchs
Teknik veriler NJ20P+U1+A2
| General specifications | ||
| Switching function | complementary | |
| Output type | PNP | |
| Rated operating distance | 20 mm | |
| Installation | non-flush | |
| Output polarity | DC | |
| Assured operating distance | 1 … 16.2 mm | |
| Reduction factor rAl | 1 | |
| Reduction factor rCu | 1 | |
| Reduction factor rSt37 | 0 | |
| Reduction factor rBrass | 1 (Minimum distance: 2 mm) | |
| Nominal ratings | ||
| Operating voltage | 10 … 30 V | |
| Switching frequency | 0 … 200 Hz | |
| Hysteresis | 1 … 10 typ. 5 % | |
| Reverse polarity protection | reverse polarity protected | |
| Short-circuit protection | pulsing | |
| Voltage drop | ≤ 3 V | |
| Operating current | 0 … 200 mA | |
| No-load supply current | ≤ 20 mA | |
| Operating voltage indicator | LED, green | |
| Switching state indicator | LED, yellow | |
| Approvals and certificates | ||
| UL approval | cULus Listed, General Purpose | |
| CSA approval | cCSAus Listed, General Purpose | |
| CCC approval | CCC approval / marking not required for products rated ≤36 V | |
| Ambient conditions | ||
| Ambient temperature | -25 … 70 °C (-13 … 158 °F) | |
| Mechanical specifications | ||
| Connection type | terminal compartment | |
| Information for connection | A maximum of two conductors with the same core cross section may be mounted on one terminal connection! tightening torque 1.2 Nm + 10 % |
|
| Core cross-section | up to 2.5 mm2 | |
| Minimum core cross-section | without wire end ferrule 0.5 mm2 , with connector sleeves 0.34 mm2 | |
| Maximum core cross-section | without wire end ferrule 2.5 mm2 , with connector sleeves 1.5 mm2 | |
| Housing material | PBT | |
| Sensing face | PBT | |
| Degree of protection | IP68 | |
